How to Draw a Bifold Door on a Floor Plan
Cartoon the Bifold Doors
Bifold doors are generally shown with each door in a half-open position to bespeak their distinctive blueprint. Although there are four door panels on the cabin'southward closet door, you will demand to describe only one, rotate it into place, and then create copies with the MIRROR command. To begin the practice, y'all will use the PAN command to shift the view of your drawing to run into the closet area without changing the zoom gene. Follow these steps:
1. Continue using I04-18-SlidingGlassDoor.dwg (M04-eighteen-
SlidingGlassDoor.dwg), or open information technology if it's not already open.
two. Start the PAN control from the View tab ➢ Navigate 2nd panel, click
the Pan button, or type P↵ at the control line. The cursor changes
advent to await like an open manus.
3. Identify the cursor nearly the upper jamb of the sliding glass door, and
then click and drag the mouse down until the drawing area
shifts to display the cupboard expanse (run into Figure 4.72).
F igu re 4 . 7 2 : Pan the view to show the closet area.
4. Press the Esc key to cease the PAN command, or correct-click and choose
Get out from the context bill of fare.
The cupboard opening is four′ (1220 mm) wide, so yous will need to make
four door panels, each one′ (305 mm) wide.
5. Commencement the Rectangle (RECTANG) control and specify the lower corner
of the right closet jamb every bit the commencement corner point. The running
Endpoint osnap ensures that the corner point is selected precisely.
6. Blazon -1,-12↵ (-25,-305↵) to create a rectangle ane″ (25 mm) wide
and 12″ (305 mm) long oriented toward the lesser of the cabin, as
shown in Figure 4.73.
F igu re 4 . 7 3 : The first closet door panel is drawn.
7. Type -45↵. The door rotates 45ยบ (meet Figure 4.74), and the ROTATE
command ends.
F igu re four . vii 4 : The first cupboard door console is rotated.
eight. Start the MIRROR command from the Home tab ➢ Alter panel, and
then select the closet door panel.
9. Verify that Ortho fashion is nonetheless turned on in the status bar. If it's not,
click the Ortho Mode button or printing the F8 shortcut key to turn on
Ortho mode.
ten. At the Specify kickoff point of mirror line: prompt, click the farleft
corner point of the selected console.
11. Move the cursor either up or downwardly until you lot run across the mirror door
panel directly to the left of the first console (see Effigy 4.75); and then click
to specify the second betoken of the mirror line.
F igu re 4 . vii 5 : Mirroring the first closet door panel
12. Printing ↵ to accept the default No option when prompted to erase the
source object.
thirteen. Start the MIRROR command again, and this time select both of the
door panels.
xiv. Choose the midpoint of the back wall of the cupboard as the showtime signal of
the mirror line.
15. Then move the cursor downwardly to mirror the existing panels
directly to the left, as shown in Figure 4.76.
F igu re 4 . 7 6 : The closet door is complete.
16. Click to ready the second point, then printing ↵ to retain the source
objects.
17. Click the Zoom Extents button to see the full floor program with all doors
(see Figure four.77).
F igu re 4 . seven 7 : The motel with the walls and doors completed
18. Save this drawing as I04A-FPLAYO.dwg (M04A-FPLAYO.dwg
Tags autocad control autocad medico autocad document autocad ebook autocad engineering autocad help autocad interface autocad learning autocad material autocad card autocad pdf autocad option autocad solution autocad tips autocad toolbars autocad grooming autocad tricks autocad tutorial autocad video how to autocad
Source: https://cadcamengineering.net/drawing-the-bifold-doors/
0 Response to "How to Draw a Bifold Door on a Floor Plan"
Post a Comment